Tech Tip: A Strategy for Bird Strike Simulations Using Abaqus/Explicit

This article was originally published in the June 2019 issue of SIMULIA Community News magazine.

A bird strike is classified as a high-velocity soft body impact because the stresses, which are generated in the contact region, are significantly greater than the strength of the bird but lower than the strength of the impacted structure. High deformability of the impactor (bird) causes spreading of the impact load over a certain area of the
structure that requires the use of special strain-rate-dependent material models.

If the structure is deformable, the impact load depends on the structural response that, in turn, depends on the impact load. Experiments show that bird strike is characterized by the following three phases: (1) shock wave stage; (2) pressure release stage; and (3) steady-state flow pressure stage [1]. Important parameters, which are obtained from the experiments, include the peaks of the impact forces and pressures and the steady flow pressure.

The bird material is described by the so-called “elastic-plastic hydrodynamic” material model, which is widely accepted in the literature. At high pressures, the hydrodynamic pressurevolume behavior of the bird can be modeled in Abaqus/ Explicit using: (a) the Mie-Grüneisen form of the equations of state with the linear Hugoniot relation between the shock wave in the bird, Us, and the particle velocity, Up, or (b) a tabulated equation of state, which provides greater flexibility in modeling the hydrodynamic response of materials.

Additionally, the Abaqus ductile damage criterion is used to prevent excessive distortion of Lagrangian elements and associated failure of the analysis, which is caused by the anticipated physical behavior (flow) of the water-like homogenized bird, through the deletion of bird elements. Element deletion also brings the results of the simulation closer to reality.

The pressure distributions over the structure with due regard for the nonlinear coupling between the bird and the target can be effectively modeled by means of the general contact capability of Abaqus/Explicit. The penalty method used in the general contact algorithm allows for accounting of the differences in the mechanical properties of the contacting bodies.

The meshing task is significantly simplified for the CEL approach because there is no need to mesh the soft projectile. Instead, a simple uniform finite element mesh is constructed from Eulerian elements so that the projectile is fully contained within the mesh boundaries throughout the analysis. This can be achieved either by creating an immovable Eulerian mesh, which is large enough to encompass the entire trajectory of the projectile from the beginning to the end of the analysis, or by creating a moving Eulerian mesh, which is capable of following, expanding, and contracting to enclose the projectile as it moves in space.

The use of a cylindrical projectile permits a direct comparison with the analytical predictions of the pressure peaks and steady flow pressures. Good correlation is observed between Abaqus and theoretical values, for both the Lagrangian and CEL methods.

The validated Abaqus soft projectile models can be directly used to analyze a given structure/structural part without having to perform a complicated and time-consuming calibration task. All the models described herein are available from SIMULIA in the Abaqus model data base format. The user needs only to substitute the rigid target in these data bases with the structure to be analyzed and run the analysis.

Detailed results can be found in the complete Best Practices document.

Katie Corey

Katie manages SIMULIA's social media, blog and online communities. As a writer and technical communicator, she is interested in and passionate about creating an impactful user experience. Katie is a native Rhode Islander and loves telling others about all it has to offer. As a self-proclaimed nerd, she enjoys a variety of hobbies including history, astronomy, science/technology, science fiction, geocaching, true crime, fashion and anything associated with nature and the outdoors. She is also mom to four amazing furbabies (2 cats and 2 dogs).

Kristina Hines

Advocacy Marketing Communications Program Manager at Dassault Systemes Simulia Corp.
Kristina is a marketing communications professional with a passion for discovering and sharing all of the innovative and cool things that Dassault Systèmes' customers are doing with simulation. When not working on the next issue of SIMULIA Community News magazine, she can be found pursuing other passions such as cooking, listening to music, coaching and/or watching her sons' soccer teams, and planning her next trip to her favorite city, New Orleans.

Latest posts by Kristina Hines (see all)

Leave a Reply